CAST Compression IP Webinar 800x100 (2)
WP_Term Object
(
    [term_id] => 157
    [name] => EDA
    [slug] => eda
    [term_group] => 0
    [term_taxonomy_id] => 157
    [taxonomy] => category
    [description] => Electronic Design Automation
    [parent] => 0
    [count] => 4178
    [filter] => raw
    [cat_ID] => 157
    [category_count] => 4178
    [category_description] => Electronic Design Automation
    [cat_name] => EDA
    [category_nicename] => eda
    [category_parent] => 0
    [is_post] => 
)

Speeding Up AMS Verification by Modeling with Real Numbers

Speeding Up AMS Verification by Modeling with Real Numbers
by Daniel Payne on 02-15-2014 at 7:00 pm

My first introduction to modeling an AMS behavior using a language was back in the 1980’s at Silicon Compilers using the Lsim simulator. Around the same time the VHDL and Verilog languages emerged to handle the modeling of both digital and some analog behaviors. The big reason to model analog behavior with a language is for… Read More


I switched to Aldec Active-HDL

I switched to Aldec Active-HDL
by Luke Miller on 02-12-2014 at 3:00 pm

I have written this before, but I was a ModelSim snob. That has changed after trying Active-HDL from Aldec. I have no plans on going back to ModelSim. You ask why? Well astute reader, great question. Unfortunately these blogs are text limited and there is no way to write about all the bells and whistles of Active-HDL. So before I continue,… Read More


Smart Strategies for Efficient Testing of 3D-ICs

Smart Strategies for Efficient Testing of 3D-ICs
by Pawan Fangaria on 02-12-2014 at 6:30 am

3D-IC has a stack of dies connected and packaged together, and therefore needs new testing strategies other than testing a single die. It’s given that a single defective die can render the whole of 3D-IC unusable, so each die in the stack must be completely and perfectly tested before its entry into that stack. Looking at it from a … Read More


Designing an SoC with 16nm FinFET

Designing an SoC with 16nm FinFET
by Daniel Payne on 02-11-2014 at 9:35 pm

IC designers contemplating the transition to 16nm FinFET technology for their next SoC need to be informed about design flow and IP changes, so TSMC teamed up with Cadence Design Systems today to present a webinar on that topic. I attended the webinar and will summarize my findings.

Shown below is a 3D layout concept of an ideal FinFET… Read More


Update on AMS Verification at DVcon

Update on AMS Verification at DVcon
by Daniel Payne on 02-09-2014 at 7:35 pm

Digital verification of SoCs is a well-understood topic and there’s a complete methodology to support it, along with many EDA vendor tools. On the AMS (Analog Mixed-Signal) side of the design world life is not so easy, mostly because there are no clear standards to follow.

To gain some clarity into AMS verification I spoke… Read More


TI – The Initial Innovator of Semiconductor ICs

TI – The Initial Innovator of Semiconductor ICs
by Pawan Fangaria on 02-09-2014 at 9:00 am


[TI’s China Foundry acquired from SMIC]

During my engineering graduation, electronic design courses and mini-projects, the ICs I used to come across were SN 7400 series from Texas Instrumentsthat covered a large range of devices from basic gates and flip-flops to counters, registers, memories, ALUs, system controllers, and… Read More


Has LinkedIn Jumped the Shark?

Has LinkedIn Jumped the Shark?
by Daniel Nenni on 02-08-2014 at 11:00 am

LinkedIn is without a doubt the number one social network for semiconductor professionals. Based on my experience, the big LinkedIn boom came with the massive unemployment during the Great Recession of 2009. In my estimate, unemployment was 12%+ at the high point in Silicon Valley and resumes clogged the internet with LinkedIn… Read More


Who Won the DesignVision Awards at DesignCon this year?

Who Won the DesignVision Awards at DesignCon this year?
by Daniel Payne on 02-07-2014 at 7:37 pm

The Seattle Seahawks had an awesome victory in the SuperBowl against the Denver Broncos, so folks living here in the Pacific Northwest are feeling proud and optimistic. The recent DesignConconference and exhibit ended 10 days ago and there were also victors announced in terms of the annual DesignVision awards that have three … Read More


Verification Execution: When will we get it right?

Verification Execution: When will we get it right?
by Daniel Payne on 02-06-2014 at 7:50 pm

Verification technologist Hemendra Talesaraattended a conference in Austin and asked me to post this article on verification execution for him as a blog. I first met Hemendra when he worked at XtremeEDA, and now he works at Synapse Design Automation – a design services company.
“In theory there is no difference between … Read More


Verification Execution: When will we get it right?

Verification Execution: When will we get it right?
by Daniel Payne on 02-06-2014 at 7:50 pm

Verification technologist Hemendra Talesaraattended a conference in Austin and asked me to post this article on verification execution for him as a blog. I first met Hemendra when he worked at XtremeEDA, and now he works at Synapse Design Automation – a design services company.
“In theory there is no difference between … Read More